Quantcast
Jump to content


PLEASE help me with my 2020 hs500 utv

joey mccarty

By joey mccarty
in Hisun UTV SxS Forum

 Share

Recommended Posts

joey mccarty Newbie

joey mccarty

Posted
Posted

I have replaced the ignition coil, spark plug, injector, fuel filter, map sensor, iac sensor, checked fuel pump and it still acts like it wants to cut out when my revs are over 3100 rpms. the problem is intermittent but happens frequently and i dont want to leave my hisun at a dealer 100 miles away and wait months. It never stalls but it idles rough and sometimes when its real bad i cant go over 10 mph. yes i fasten seat belts

ElbowRoom Rookie

ElbowRoom

Posted
Posted

Just a guess based on a similar problem I had. It seems to be going into limp mode. This is often caused by air in the radiator hoses. If so, raise front end by at least 20 inches, remove rad cap and idle machine until all air bubbles are out while adding coolant. If the problem keeps coming back, there's a coolant leak which needs to be fixed.

  • 6 months later...
mharmon12 Newbie

mharmon12

Posted
Posted

My sister had me check out her 2020 HiSun HS500 UTV.
It never cut out for me because I wore the seat belt.

There is a safety that will make the engine cut-out when the safety-belt isn't fastened.

The way to override this is to wear the seat-belt or to disconnect the sensor wire behind the seat.

Good luck with your machine!

 

Mike H

Meridian, Idaho

  • 1 year later...
jackson Newbie

jackson

Posted
Posted

I would like to change the spark plug in my 2020 Hisun 500 HO side by side, thing is I can't find the plug. All the diagrams show a plug and a line, but not where it is. Is it under one of the plates, built into the housing, in the back tire, WHERE. My e mail [email protected]. I am getting mad, the manual is not made for americans to read. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Homeowner A
      Black O2 Sensor?
      By Homeowner A
      I've been having misfire issues with my UTV 400 when it gets warm and I've thrown all kinds of parts at it so far with no permanent resolution.  Today I removed the O2 sensor and it is black on the end.  To me that means it's running rich and/or the sensor isn't working.  I replaced the sensor with a new one and will see how it goes I guess.  With EFI, I'm wondering why the sensor would be this way with low hours and mileage?  Is there a way to adjust or lean out fueling on these?  Thanks in advance.  
    • Matthew Smith
      SXS No Crank at the Key and No Spark
      By Matthew Smith
      2013 Bennche Bighorn 700 EFI
       I just picked up this project that I was told would crank, but not start.  This is what I’ve figured out so far….
      I installed a new battery and get all dash lights, head lights, and brake lights on when turning the ignition on.  Fuel pump even turns on.  It does not crank with the key, but would when I jumped the starter solenoid, so I replaced it…..no change.
      Figured I’d check for spark and compression while I was dorking around.  Compression is 150 psi, but there is no spark.  Replaced the spark plug… no change.
      So, is my new starter solenoid bad?  Could it be the brake or gear position switches even though the brakes and neutral lights come on?  Not sure where to go from here.




    • D MAYNARD
      Axis 500 4x4 turns over but no spark
      By D MAYNARD
      I have an Axis 500 4x4 UTV that I was given.  It looks like an almost new machine with 39 hrs on it however it was apparently under water from the hurricane . I have no spark at the plug. I have replaced the plug, the plug wire, & the stator so far. Can anyone advise me of what i need to check and or replace to get this thing running? Any advise would be greatly appreciated. 
                                    Thank You,
                                  D Maynard 
       
    • Homeowner A
      Coleman 400 cut out when hot under load ideas?
      By Homeowner A
      Have a Coleman UTV 400 that cranks, runs, drives well until it gets warm and is put under load.  Light throttle or full throttle it doesn't bog, but it will cut out mid throttle if you move the pedal quicker than it seems to like for example when you're getting ready to go up a hill, but if you immediately floor it, it will do just fine and not cut out.  It's random if and when it's going to do it, but is consistent in that it happens only when hot/full operating temperature.  I've replaced the injector twice, same with the spark plug and tried different heat ranges (NGK 7,8 and 8 iridium), replaced the fuel pump, adjusted the valves, checked air filter which is like new, changed the oil, replaced the fuel filter.  No check engine light.  I don't have a code reader for this.  Initially I thought it might have a head or head gasket issue as when I got it, the oil was over full, very runny like water milky and it was smoking.  I've changed the oil since then twice to clear and clean everything out, and it seems to be good.  Coolant stays the same level and so does oil with no changes in consistency or need for adding more. Had I think 7-9 miles when I got it and now has about 77.  What should I try or consider next?  
    • Homeowner A
      UT 400 Injector Upgrade?
      By Homeowner A
      Is there a better performing higher volume injector than what they come with or what is the best replacement for the original?  

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...