Quantcast
Jump to content


2015 MSU 500 - Oil problem has me stumped

CDT540

By CDT540
in Massimo UTV SxS Forum

 Share

Recommended Posts

CDT540 Rookie

CDT540

Posted
Posted

Just bought a used 2015 MSU 500.  I am in the process of replacing all the fluids and generally going over everything.  I pulled the outer plastic clutch cover off and oil started dripping out.  Oil was everywhere, a huge mess.  I thought for sure I had a bad seal on the clutch or secondary.  So I removed the clutch and secondary CVT so I could get a look at the seals and they both were dry as a bone.  The only two dry spots.  Now I  am stumped.  If oil did not get into the by way of the two shaft seals, how on earth could it have gotten in?  

Thanks

Chris

IMG_2286.jpg

IMG_2285.jpg

  • 3 weeks later...
Lucas Lenartowicz Rookie

Lucas Lenartowicz

Posted
Posted

Have you checked out the vent that from the top of the crank case to the air box? Except that is on the left hand side I believe unless they changed it (we have a 2008 hisun 700 utv) but I heard that there used is an air/oil separator there and in our case it was missing/destroyed and that led to oil splashing everywhere. I just connected the two ends of the air tubes without that separator and it works fine. Also on our hisun under that fan cover there is a little timing window that unscrews so maybe that is missing in your case. Just ideas as I heard somewhere that hisun makes the engines for massimo. But it may be a different setup as your pics do not look too familiar to me 🙃

CDT540 Rookie

CDT540

Posted
  • Author
Posted

Well I cleaned everything up and and replaced the wet clutch, outer clutch and belt.  I have been driving it around the neighborhood without the outer cover on so I could keep an eye on things and all seems to be good and dry.   I don't see how it could create the mess but one thing that was amiss was the oil filter wasn't even finger tight.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Similar Topics

    • Homeowner A
      UT400 First Oil Change Overfull Milk Chocolate What to Check
      By Homeowner A
      Picked up an essentially new 2022 UT400 with 9 miles on it.  Decided to change the oil because it's probably never been done.  Pulled the dipstick and noticed it was overfull then went and pulled the drain plug and took off the filter and it was like brown water running out.  What should I start checking?
    • Cory J
      2023 t-boss 550 belt slipping and found oil in belt housing
      By Cory J
      Belt started slipping when I used it in high gear. It works okay in low unless I'm trying to power it up a hill and then it slips.., Ordered a new belt and went to change it and found a good bit of oil in the belt housing. Has anyone experienced this? Belt looks fine. Only have 300 miles on this thing..
    • NC4wd
      Axis 500 Lift Kit
      By NC4wd
      Has anyone found a lift kit that fits an Axis 500? Mine is a 2021.
    • Jacob E freeman
      2018 cub cadet challenger 750 over heats no one knows why
      By Jacob E freeman
      I have a 2018 cub cadet challenger 750 I bought brand new almost 2 years ago the first month I had it the exhaust broke and burnt the spark plug wire in two that was a recall so the dealership installed the new one it had a different design and it bolted up to the bottom two plugs below the spark plug the dealership said they had to Adjust the exhaust valves I get the machine back thanking everything is good now wrong not even a week after I get it back the timing chain tensioner comes apart inside the motor I take it back to the dealership They put one on I get the machine back thanking everything is good but then just like before not even a week goes by when I was riding the Machine automatically quits going come to find out the wet clutch was burned up the primary clutch head stripped off of the splines I get that fixed and then  it overheats I take it back they bleed the air out of the coolant they bring it back to me the same day that I get it back it overheats again I take it back they temporarily fix it again just enough to let the warranty run out and now the machine has been to multiple different mechanics I have had them try to bleed the air out they have stood it up on its end I have had the water pump changed I have had the fan hooked to a switch so I could leave it on all the time but still almost 2 years later not even 200 hours on the machine and I cannot ride it The dealership will not take it back as a lemon I have tried I am at my wits end I have no clue what to try next
    • Greg Kilgore
      Heater installed 2021 Axis 500
      By Greg Kilgore
      Last year bought a small universal coolant style cab heater. Well I installed it today. Thanks to another member, RangeRider45, and his install
       
      That told in his post the size fitting he used. I got the same fittings plus a few others. And all went kinda smooth. Took a few minutes to get air purged from coolant system. Should have parked on hill with front up in the air. But would have had a hard time working on it.
      I had a variable power switch connected to an overhead cab fan. Never really used the fan that much. And I have to remove the fan to put on my cab enclosure anyway. So I repurposed the switch to supply power for the heater. The heater has 2 12-volt DC computer fans that are rated for 1.8 amps each. So it's not going to be a big drain on the weak charging system. And with the switch I've got great control over the speed of the fans.
      If anyone is interested the radiator hoses are 7/8 inch. I reworked the temperature sending unit (moved it closer to radiator) to make room for all the extra plumbing I did to get the heater to work the way I wanted. 
      Plumbing parts list.
      10-15 worm water clamps. 3/4 to 1 1/4 inch size.
      2 1" x 3/4" x 1" PEX Tee
      1 3/4" PEX ball valve
      1 1" PEX ball valve
      5/8" heater hose. I got 6' and probably have 4' left over.
      I used the radiator house I cut out to use as splices between the PEX fittings. The PEX fittings are not true to their dimensions that are stated on the package. So they fit the 5/8" and 7/8" very nicely.
      They way I have it plumbed is from radiation out side. A tee, then the 1" ball valve, then a Tee. Coming off the Tees are the hoses going to the heater core. There is a 3/4" ball valve on one of the Tees. The ball valves are used to bypass the heater core in the summer. Or direct the hot coolant through the heater core in winter. The temperature sending unit tells me how hot the coolant is. And if anything is getting too hot. The dash also has an idiot light that comes on if the head gets too hot. But doesn't do anything if the radiator gets too hot. There is a temp sensor on the radiator that controls the electrical fan. But if the coolant isn't circulating. That switch never sends a signal to turn on the fan. But enough talking/rambling. Everyone wants to see pics. The only thing I need to change is the orientation of the handle on the 1" ball valve. I have 2" or more clearance between the handle and the tire when cut hard right. But I still don't like it. And instead of taking the valve out and rotating 180°. I'm just going to take the nut off and rotate the handle 180°. Think I need to make a locking mechanism to lock the handles in place so they don't vibrate closed when the machine is moving.
      The temperature sending unit and housing. Size 22 mm. Aluminum from Amazon.

      Upper Tee the lower Tee is identical. Can also see the handle of the 3/4" ball valve on the 5/8" hose going to the heater.

      The 1" ball valve. Goes between the 2 Tees

      Wide view of the plumbing.

      The heater installed in the sxs. The 3 black hoses are just hanging there. Zip ties to the heater but not attached to any thing. Will probably just direct 2 toward the wife's feet. And 1 toward mine. Or what ever is need as the heat is needed on rides. The black hose in passenger floorboard is some 1" hose that is not needed. Don't know what I'll do with it.

       
      I think if I was going to do it again. I'd put some Indian Head gasket dressing or silicone on the 1" side of the PEX fittings. And I may still do that. But I really hate the ideal of introducing air back in the coolant system.
       
      Any questions just ask. It may take a while to answer. But I'll try.
      Ya be good and stay warm over the next few months 
       
      Kilgore.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...