Quantcast
Jump to content


2015 MSU 500 Belt

CDT540

By CDT540
in Massimo UTV SxS Forum

 Share

Recommended Posts

CDT540 Rookie

CDT540

Posted
Posted

I need to replace the belt for the clutch.  I see there are numerous off brands on Amazon.  Is there a particular brand that is better than the others?  I have an old CJ7 that I work on a lot and there are certain vendors that sell total junk and should be avoided.  Just checking to see if there are any brands/dealers to stay away from.  I saw a video on YouTube where they used a Gates but I don't see Massimo listed on the parts chart.  If you use 2015 Bennche Big Horn 500 you get part number 21G3353.  Anyone use that Gates belt?

Thanks

Chris

Greg Kilgore Collaborator

Greg Kilgore

Posted
Posted

Don't have a Massimo. I have a 2013 CFMOTO UForce 600.

But I did order a Gates belt off Amazon.

I went to the Gates website and crossed my part number over to the Gates belt.

All good. 

FWIW, I thought the belt was my issue but turned out to be the wet clutch in my case.

While I had rear of machine up in the air everything worked fine. BUT when I put the rear tires on ground with CVT cover off. 

Had wife put in gear and give a little gas. The nothing wanted to move. This told me the wet clutch was bad. Ordered that off Amazon also. Just don't put the one-way bearing in backward if you have one. 

 

All hope for the best. But the Gates belt are good. At least for me.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Similar Topics

    • Cory J
      2023 t-boss 550 belt slipping and found oil in belt housing
      By Cory J
      Belt started slipping when I used it in high gear. It works okay in low unless I'm trying to power it up a hill and then it slips.., Ordered a new belt and went to change it and found a good bit of oil in the belt housing. Has anyone experienced this? Belt looks fine. Only have 300 miles on this thing..
    • Frank in MI
      New old guy
      By Frank in MI
      Thanks for accepting me!
      Haven't got a side by side yet, but have been shopping.   
      Any advice welcome & I am on a limited budget, so haven't decided yet on new or used.
       
    • hisun junk
      2017 Cub Cadet Challenger 750 hisun junk motor
      By hisun junk
      As I tried to do a conversion with the Yamaha 660 motor, I realized the 660 was never fuel injected so it would not work for the fuel injected hisun motor swap. But the good thing is the hisun 750 motor is a clone of the 660 Yamaha but with the components for the fuel injection (cam/crank position sensor). So that left me with a new rebuilt Yamaha 660 and still a broke 750 hisun motor. I took apart 750 think the timing chain had broke from all that I've heard about these motors. The chain was not broke, but just off cam and crank gears! The chain tensioner was at fault!  I've ordered Yamaha 660 replacement parts, chain, two exhaust valves (which got bent when chain came off while motor was spinning) and seals. The piston has 2 little nicks where it had hit valves but no damage otherwise. The head is being redone at the machine shop and I'll be putting it back together in the next couple of weeks. Also I finally tracked down a Service Manual with all the info on the 550/750 Challenger.

    • Hunterman22
      2021 Hisun Axis 500 No Start - Need Help Please
      By Hunterman22
      2021 Hisun Axis 500 UTV (From Lowes)
      Will NOT START
      MY apologies if this is to much info just wanted to give yal the most information possible for help.
      I'm a so called diyer. An Electrician by trade 21yrs. I got my S×S from my last job. The contractor purchased this S×S for this specific job brand new, from Lowes. They used it for hauling materials, tools, & a little bit of anything you can think of on an Industrial type job site. 
      I remember getting on the SxS one time & pushed the gas petal all the way to the floor & SxS had very little power. 
      So anyway ,when the job finished up back mid July this year (7/2024) , I asked the contractor what they was going to do with it. I was told to take it. Otherwise it would go to the contractors yard (storage yard) & most likely rust away. 
      Took it home washed it , it had a heavy coat of dust on it & in it dust was every where. My helper & I had to push it on the trailer to get it home.  After washing it throughly I let it sit & dry out for a good day and half, maybe 2 days. Before trying to start it. NO START. Will turn over & try to start but thats it. 
      So here's what I've purchased & installed. New Air Filter, new spark plug, new air idle control valve (AICV), new throttle position sensor, new throttle body, new oxygen sensor, new digital dash speedometer/fuel gauge/clock. 
      Also drained the old oil & gas & replaced with new oil & 93oct. gas. I should probably mention that I've changed the AICV twice. The 1st time I changed the AICV I was able to get the SxS started & let idle for at least 10-15min. Drove out of the garage, with very little power,  turned it around & barely got it back in the garage.That was the one & only time I've been able to start the SxS. I've also cleaned the Throttle Body and & intake with TB cleaner.  So after that the AICV was  making weird noise so I pulled it out & tried cleaning it, pretty sure I messed it up. So I purchased a Throttle Body that came with new AICV & TPS. Still NO START.  I've checked the fuel pump & the fuel injector.  I took the injector off still hooked up to wiring & turned the key over, the injector sprayed a lot of gas out kinda the size of a volleyball. I've also checked the clearance gap on the intake & exhaust valve. But today 11/2/2024 I'm going recheck spark plug gap & the valve gaps. And alot of other checking. Would the driver side seat belt have anything to do with it not starting?? I know the driver side seat belt has to be in gauged for full throttle "going fast". Thing is the drv. side seat belt will latch but feels like might be messed up inside of it. Tired opening it up but to no avail.  I've never had a S×S or 4wheeler so I was really excited when I got the S×S,not so much anymore.  I work on & fix my own vehicles usually no problems.  But this SxS is kicking my ass.
      So if possible & someone could help me with some ideas or tell me what Im doing wrong or did wrong, I would greatly appreciate it.  Thank you for reading thus far.
       
       
    • Josh5696
      2022 Axis 500 clutch noises on deceleration
      By Josh5696
      So I've got a 2022 Axis 500 UTV with only 50 miles on the odometer. It seems to have a strange grinding/squeeling noise coming from the clutch when decelerating or going down hill at lower speeds. Did some research, and found out this is apparently a fairly common thing. Alot of sources suggest the one way bearing is responsible. I'm hearing about quite a few horror stories about these bearings going bad on practically new machines, and when they replace the bearing it goes bad again shortly after.
      Has anyone come up with a solid fix for this? I've read it may be possible to run the UTV without the bearing at all, is that true? Are the $20 replacement bearings from eBay and Amazon complete garbage, and is there a better one way bearing out there that's built stronger? Is there something else causing this bearing to wear out faster, or is the stock bearing complete junk?
      Any input is appreciated, thanks in advance!

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...