Quantcast
Jump to content


HiSun Sector E1 Error code E038 and E013 what does it mean?

Jurg

By Jurg
in Hisun UTV SxS Forum

 Share

Recommended Posts

Jurg Newbie

Jurg

Posted
Posted

Trying to charge over night I found the unit with a flashing amber LED both in the dash and on the charger next to the lh front wheel. 

The first error code I got was E038 on the charger with my next attempt I got E013.  The battery is not being charged.

??

BuggyBoy Apprentice

BuggyBoy

Posted
Posted

E013 is an issue with loose connection or an external device interfering with charging. 
got same with mine but can’t see any loose wires or connections and no other device has been installed. 

have emailed manufacturer of charger with details and data log from charger. 
 

did you resolve it?

BuggyBoy Apprentice

BuggyBoy

Posted
Posted

'E013 - Charger Output Current NotAccepted - Battery voltage is detected but the charger is unable to output current. This is normally caused by an electrical device connected between the charger and the battery which passes through voltage but not current.  Poor connections can also cause this.  Ensure the charger is properly connected to approved equipment. This error will automatically clear once the charger is reset by cycling DC or AC'.

EVSupport Contributor

EVSupport

Posted
Posted

Suggest you check all the cabling back to the main connections to the battery pack. They are under the central hoop under the seat look for the connector with the plastic block and two leads, thats one of the charge cables. The second lead  is the temp sensor lead in that plastic  block. But check all the battery connections. Also check under the cover of the Delta Q charger on the right (passenger side ) side are all the wire connections take off the cover (two torx screws) and then carefully check the tightness of the torx screws holding the two larger charge leads . Its easier to take the front wheel off than simply inserting your head between the wheel and the front arch.

BuggyBoy Apprentice

BuggyBoy

Posted
Posted

Took off the small cover on charger and cables look ok and were all tight. 
however, decided to add another pos cable to bypass current pos cable from charger to battery as a test before I dismantled for warranty testing/return and it worked, now charging and no fault. 
The Pos/Neg charger cables seem too small a gauge for the current (3-4mm?) going through them.  I’m going to upgrade the charging harness to 6mm to stop overheating and cable breakdown. 
Thanks for your advice. Are you Hisun EV support or independent? 

Jurg Newbie

Jurg

Posted
  • Author
Posted

There was a loose connection on the front battery, second row from the left. On the same row one battery back there is a connection with a (former) 30 amp fuse holder. That connection on the battery was not completely tightened. But the fuse holder cap was unusually bulged and the cap fused to the body. Further investigation revealed that the fuse inside was completely melted and disintegrated. I am going to fix that and hope that this will resolve the problem. It definitely looks like all your comments are correct. Thanks to everybody!

 

EVSupport Contributor

EVSupport

Posted
Posted

The cable for the charger DC side  is normally quite adequate. You will struggle to get larger in to the housing easily. Dont solder only crimp. If you cant crimp get someone who can. And you will need to ensure the negative side has the temp sensor connection.

Im not  connected to Hisun, but I do Hisun E1 Li Ion conversions in the UK. So see them on an almost constant basis.

BuggyBoy Apprentice

BuggyBoy

Posted
Posted

I’d love to convert mine to Lithium batteries. 
I think I’ve read one of your posts a few years ago where you said it’s actually not that difficult, just time consuming. You mentioned changing an algorithm in the battery controller or charger from memory? Apart from physically fitting the batteries, is that about it?

EVSupport Contributor

EVSupport

Posted
Posted

All new steel and ally battery enclosures, all new battery / connection cabling,  New loom for the Battery management / Vehicle interface/ charger, new small display, New algorithm on the Charger, re programe the Sevcon , New rear arch cover sections to reduce crud. New mains inlet and relay box in the front compartment. So not a lot , just takes me about 4 days start to finish  with all the parts ready made and in stock.  Some photos on my EV Support Facebook page   https://www.facebook.com/EVSupportUK

 

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Homeowner A
      Diagnostic Trouble Code Help?
      By Homeowner A
      I was randomly and briefly able to connect to my Coleman UTV 400s ECU the other day twice and haven't been able to since.  When I was able to access it, I found the following codes and wondered if anyone may know where I should start or what I should look at?  
      P0031 - O2 Sensor Heater Control Voltage Low
      P0107 - Manifold Absolute Pressure/Barometer Pressure Voltage Low
      P0113 - Intake Air Temperature Sensor Voltage High
      P0118 - Engine Coolant Temperature Sensor Voltage High
      P0650 - Malfunction Indicator Lamp (MIL) failure
       
    • Gorj
      Sector E1 Battery change out
      By Gorj
      I am going to replace the batteries in my E1. I am not interested in the high cost Lithium or the expensive 6 volt dry batteries.  I am considering four 12 volt deep charge marine batteries. I have a source for 810 amp units for about $100 each.  I have no worries about reprograming the charger because it went out a few years ago and I replaced it with generic golf cart charger. When I decide to do this, I'll keep you posted on the results.
    • Homeowner A
      Code Reader for Delphi MT05 Coleman UTV 400 Hisun
      By Homeowner A
      Is there a code reader available for the Coleman UTV 400?  I tried using the HUD ECU Hacker software and cables/adapters but no luck OBD to delphi 6 pin and KKL VAG as well as ELM327.  Will not connect.  I was able to get it to connect randomly a couple of times, but haven't been able to since.  I was able to clear and read the codes briefly.  I'm aware of the Tiny Scan 301 but it doesn't seem to be readily available.  There's a few out there but they are expensive.  
    • aefron88
      HOWTO- Code Scanner & Read Engine Parameters
      By aefron88
      This post will explain how to hook up your PC to the ECU of a Hisun/Coleman/Etc UTV to be able to read error codes & engine parameters for troubleshooting purposes.
      This is applicable to all small engines using the Delphi MT-05 ECU. This should cover all fuel injected Hisun models, as well as various other Chinese FI engines, as the Delphi MT-05 ECU seems to be the favored ECU solution.
      Even though we get actual engine error codes to display on the dash, sometimes we have “pending codes” (not yet confirmed by the ECU) or other intermittent issues that are hard to diagnose, for example a poorly connected sensor that may give intermittent false readings, or a sensor that’s putting out bad date, but not bad enough for the ECU to realize.
      The setup requires 2 cables, which are available for around $25 combined, a PC with a USB port, and some charityware software called “HUD ECU Hacker”. This gives the same functionality as the $300 dealer code scanner for a fraction of the price.
      In searching I found info about HUD ECU Hacker, but I have yet to see info anywhere about how to hook it up to a Hisun, so I took the leap and bought some cables, and made it work. I will show a step by step of how to do so in post two.
      I will be breaking this down into 2 posts:
      Delphi ECU Info & Overview (This post) System setup & use Delphi ECU Info (Skip ahead to the next post if your eyes glaze over technical details)
      The Delphi MT-05 ECU was developed to allow small engines to use fuel injection. A fuel injection system requires feedback from various sensors to operate efficiently. This feedback allows the adjustment of ignition timing, fuel injection volume, etc to efficiently and cleanly produce the most power possible from a given engine.
      The MT-05 ECU has a number of sensors that are required for proper functioning including; Coolant temp, crankshaft position, intake temp, intake pressure, exhaust O2, throttle position, as well as some other optional sensors that are used on more complex vehicles.
      From the sensors the ECU adjusts: Fuel injector timing/pulse, Idle air control valve, and ignition coil

      The Delphi MT-05 puts out diagnostic data, however it is not ODB2 like a modern car, where is where it gets tricky reading it. There are three options, there is an old 16 bit piece of software Delphi has that is not able to run on a modern computer, there is the motorscanner tool for dealers ($300), or there is freeware HUD ECU Hacker with the proper cables.
    • clint501
      Hisun E1 charger not working
      By clint501
      I recently purchased a Hisun E1 and the other day the charger stopped working properly. The LED on the dash blinks red & green and the light on the side of the charger also blinks red & green. The fan on the charger does not come on like it used to do. There is no error code that I can see. Does anyone have any suggestions to remedy this?

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...