Quantcast
Jump to content


2017 Arctic Cat

David Campbell
 Share

Recommended Posts

David Campbell Newbie

David Campbell

Posted
Posted

We are looking at buying our 1st side by side the local dealer has a used 2014 Arctic Cat wilderness se. I've seen mixed reviews on that machine. Can you guys give me some info on it if its a good reliable unit. 

  • Alex changed the title to 2017 Arctic Cat

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Similar Topics

    • mark walkom
      sector e1 regen has stopped (mostly) working
      By mark walkom
      the regen braking on my e1 has stopped working unless (for eg) I am going down a hill in low and it's slowing things down to stick to the 10kph limit. when I drive and take my foot off the accelerator it's not initiating the regen to slow things down and instead just coasts at whatever speed it is at, or speeds up as the regen is not limiting it. the brake lights work, so it's probably not a fault with the sensor on the brake pedal
       
      hoping someone else might be able to provide some suggestions on things to check, as the mob that I bought it off seem to have gone silent on me
    • shawn b
      2020 hisun 400 utv side by side
      By shawn b
      my hisun died on me while driving it started losing power then stalled. it wants to start but wont . it didn't over heat. I replaced plug,fuel filter injector, and fuel pump.put code reader on it and says no codes. have any ideas possibly sensor? Any input on what it could be would be appreciated
    • tskm
      2014 Artic cat “wildcat” 1000 rear diff
      By tskm
      in desperate need of a rear differential for my 2014 wildcat 1000. It has blown up right in the midst of the hurricane that struck us here in N/W N.C. I could really use this machine right now. No luck finding this from Artic Cat or the many numerous online vendors. Any info or resources wil be greatly appreciated !
      Tom 
    • TPlummer
      Axis x550 02 sensor on right after buying the UTV.
      By TPlummer
      We recently purchased the Axis x550. Fueled it with 93 fuel and drove one time around the farm and the 02 fault error appeared. Any ideas? 
    • redneckred
      Gremlins in the machine
      By redneckred
      I have a 2012 Bennche Bighorn 700X.  I bought it used.  It had been sitting in a field for several years untouched.  I put a new sun gear in the shifter, new shifter linkage due to the old one having been patched, and a new battery (and of course fresh fuel).  The machine cranked and ran beautifully.  I had it over a year and then the machine quit running.  As it would not stay cranked, I narrowed the problem down to a bad IAC valve.  I replaced it and it ran as good as new/old.  Fast forward, the machine started to act like reverse wasn't catching and would not always back up when in gear.  Then forward quit.  I assumed a bad CVT belt and got one.  Started removing the bolts from the cover and (3) just turn in the housing without coming loose.  (2) are on the bottom, so very little room to do anything with them.  I tried cranking the machine again to see the belt move since I can move the cover enough to see the belt and now the machine will not crank.  It turns over fine.  It gets gas to the injector and has spark.  I can spray cleaner down her throat and she would run until it ran out.  I have replaced the IAC twice and put a new injector with no change.  I went out and put the old injector back in to see if that made any difference and, well, it did.  I tried to crank the machine and the starter is stuck trying to turn the machine over even with the key off.  I have to disconnect the battery to stop it.  Before I shoot this thing, what am I missing?  Is this an ECM problem or something else I am not seeing?  Been dealing with these Gremlins for over a month now and weeds are starting to overtake the motor due to it not moving.  I would love to get the thing running first and any ideas of getting those CVT cover bolts out would be extremely helpful.  Thanks in advance.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...