Quantcast
Jump to content


Recommended Posts

Posted

Yesterday my Trooper blew the fan circuit fuse. The book says it should be 25amp and it had a 20amp installed. If anyone can tell which wire under the hood is the fan wire I would really appreciate it. The instrument power has been intermittent at times and I suspect the two failures may be related.

As a side note: I did my first oil change - - boy was that fun!!! My car has the welded in skid pan so I had to cut a hole to allow the oil to drain without creating a mess. After trying several ways to make the hole I finally ended up cutting it with my die grinder with a 3" cutting wheel. To contain the oil I got a canning funnel (has high sides and a wide mouth) to direct the oil unto the catch pan.

I was real proud of myself - didn't spill a drop ---- until I kicked the dirty oil can. Oh well! Murphy lives at my house.

Any words of wisdom will be appreciated.

Gumball

Posted

The fuse box is on the left side of the driver behind you. you can figure out which fuse is bad with a test light touching the end of the fuse with out pulling them out. there is metal exposed on each side of the fuse.

Posted

Hi Flatbed,

Thanks for the information. Just to keep everything exciting Joyner put the fuse box on my Trooper right behind the passenger seat. I did discover which fuse was blown but would like to know what color wire and were it's located in the instrument panel. I know is goes somewhere through the dash because it's tied in with the ignition switch when starting.

Reading the manual is a real challange.

Thanks again for the input. It is appreciated.

Gumball

Posted

I doubt the wire goes to the panel, maybe to the relay box which is controlled by the computer. Open up http://www.utvboard.com/post-a88-.html and save your self a copy, it's an electrical wiring diagram.

For your oil, I suggest http://www.quickoildrainvalve.com/SearchResults.asp?Cat=210, take a look at Parts, Pieces, and Information for our Troopers, usually the 3rd topic under troopers and you should change the oil in your differentials also. At least open the fill plug and dip the oil to see what it looks like. Mine was silvery the first time I did mine. one bottle does both diffs.2093207660104110397PpxreP_th.jpg

It probably wasn't your fault that the dirty oil got spilled, it was one of those garage gremlins that hide tools, move parts and pushes things of your bench all the time.

Kinarfi

Posted

Thank you Kinarfi,

I downloaded the schematic and now all I have to do is learn Chinese - ah sow!

Your idea is a good one. Putting a petcock on the oil drain should be quite safe from harm considering where it's buried.

I will definitely look into that.

Geez, you have a gremlin at your place too. He sure has a lot of relatives.

You folks on this board are awesome. It's good to be a part of it.

Enjoy your evening!

Gumball

Posted

Every time my Trooper broke this winter I would wash it before taking it to my dealer. He got tired of replacing fuses from the frozen fan so he hooked me up with a breaker.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By CapnWalleye
      Just picked up a Hisun 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • By FTG-05
      I want to ditch my Kubota RTV-XG850 and its moronic twitchy throttle design flaw, get rid of the problematic engine and the 40 mph purposely throttled speed.
      So far, I'm looking at the Honda Pioneer 1000 and the Polaris Ranger 1000, both of which have 1000-1500 lb payload bed capacity.
      What other makes and models should I be looking at?
       
      Thanks for the help!
    • By Grant
      I recently bought an axis 500 and it’s missing a box or something the plug is L shaped I’ve looked through the wiring diagrams and still can’t figure it out. The plug is located right near the battery housing 

    • By A P
      Hi
      I have a 2022 hisun sector eps 550. 30amp fuse is blown for eps. Checked the motor and it’s fine. Opened up the controller and found a bad diode. Dealer wanted 500$ for the controller. Just posting this in case it helps someone. I couldn’t read numbers from the old one so just took a guess and replaced it with a 100v 3amp diode. 
    • By rdborra
      I had to remove the relay for the dump bed due to it popping the fuse for main key power. I have tried to find a short but nothing seems to out of normal. I also disconnected the dump motor and switch and still pops the fuse. Also, when the machine is warmed up i get about 5 to 10 of work out of before it stalls. Once I can get it to start again I have to use the choke to keep it running. 
×
×
  • Create New...