Quantcast
Jump to content


Recommended Posts

Posted

Yesterday my Trooper blew the fan circuit fuse. The book says it should be 25amp and it had a 20amp installed. If anyone can tell which wire under the hood is the fan wire I would really appreciate it. The instrument power has been intermittent at times and I suspect the two failures may be related.

As a side note: I did my first oil change - - boy was that fun!!! My car has the welded in skid pan so I had to cut a hole to allow the oil to drain without creating a mess. After trying several ways to make the hole I finally ended up cutting it with my die grinder with a 3" cutting wheel. To contain the oil I got a canning funnel (has high sides and a wide mouth) to direct the oil unto the catch pan.

I was real proud of myself - didn't spill a drop ---- until I kicked the dirty oil can. Oh well! Murphy lives at my house.

Any words of wisdom will be appreciated.

Gumball

Posted

The fuse box is on the left side of the driver behind you. you can figure out which fuse is bad with a test light touching the end of the fuse with out pulling them out. there is metal exposed on each side of the fuse.

Posted

Hi Flatbed,

Thanks for the information. Just to keep everything exciting Joyner put the fuse box on my Trooper right behind the passenger seat. I did discover which fuse was blown but would like to know what color wire and were it's located in the instrument panel. I know is goes somewhere through the dash because it's tied in with the ignition switch when starting.

Reading the manual is a real challange.

Thanks again for the input. It is appreciated.

Gumball

Posted

I doubt the wire goes to the panel, maybe to the relay box which is controlled by the computer. Open up http://www.utvboard.com/post-a88-.html and save your self a copy, it's an electrical wiring diagram.

For your oil, I suggest http://www.quickoildrainvalve.com/SearchResults.asp?Cat=210, take a look at Parts, Pieces, and Information for our Troopers, usually the 3rd topic under troopers and you should change the oil in your differentials also. At least open the fill plug and dip the oil to see what it looks like. Mine was silvery the first time I did mine. one bottle does both diffs.2093207660104110397PpxreP_th.jpg

It probably wasn't your fault that the dirty oil got spilled, it was one of those garage gremlins that hide tools, move parts and pushes things of your bench all the time.

Kinarfi

Posted

Thank you Kinarfi,

I downloaded the schematic and now all I have to do is learn Chinese - ah sow!

Your idea is a good one. Putting a petcock on the oil drain should be quite safe from harm considering where it's buried.

I will definitely look into that.

Geez, you have a gremlin at your place too. He sure has a lot of relatives.

You folks on this board are awesome. It's good to be a part of it.

Enjoy your evening!

Gumball

Posted

Every time my Trooper broke this winter I would wash it before taking it to my dealer. He got tired of replacing fuses from the frozen fan so he hooked me up with a breaker.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Topics

    • By SouthernGypsy
      We have a 2018 Cub Cadet Challenger 400 and I found this Internally Threaded Bolt with a 10mm head size laying in the floor of the shop bay here on our ranch where we park the Cub Cadet.
      Trying to figure out where it belongs...
       




    • By se3388
      Hopefully someone else will buy a UT10X and join in.
       
      Steve.............
    • By A P
      Hi
      I have a 2022 hisun sector eps 550. 30amp fuse is blown for eps. Checked the motor and it’s fine. Opened up the controller and found a bad diode. Dealer wanted 500$ for the controller. Just posting this in case it helps someone. I couldn’t read numbers from the old one so just took a guess and replaced it with a 100v 3amp diode. 
    • By Greg Kilgore
      Last year bought a small universal coolant style cab heater. Well I installed it today. Thanks to another member, RangeRider45, and his install
       
      That told in his post the size fitting he used. I got the same fittings plus a few others. And all went kinda smooth. Took a few minutes to get air purged from coolant system. Should have parked on hill with front up in the air. But would have had a hard time working on it.
      I had a variable power switch connected to an overhead cab fan. Never really used the fan that much. And I have to remove the fan to put on my cab enclosure anyway. So I repurposed the switch to supply power for the heater. The heater has 2 12-volt DC computer fans that are rated for 1.8 amps each. So it's not going to be a big drain on the weak charging system. And with the switch I've got great control over the speed of the fans.
      If anyone is interested the radiator hoses are 7/8 inch. I reworked the temperature sending unit (moved it closer to radiator) to make room for all the extra plumbing I did to get the heater to work the way I wanted. 
      Plumbing parts list.
      10-15 worm water clamps. 3/4 to 1 1/4 inch size.
      2 1" x 3/4" x 1" PEX Tee
      1 3/4" PEX ball valve
      1 1" PEX ball valve
      5/8" heater hose. I got 6' and probably have 4' left over.
      I used the radiator house I cut out to use as splices between the PEX fittings. The PEX fittings are not true to their dimensions that are stated on the package. So they fit the 5/8" and 7/8" very nicely.
      They way I have it plumbed is from radiation out side. A tee, then the 1" ball valve, then a Tee. Coming off the Tees are the hoses going to the heater core. There is a 3/4" ball valve on one of the Tees. The ball valves are used to bypass the heater core in the summer. Or direct the hot coolant through the heater core in winter. The temperature sending unit tells me how hot the coolant is. And if anything is getting too hot. The dash also has an idiot light that comes on if the head gets too hot. But doesn't do anything if the radiator gets too hot. There is a temp sensor on the radiator that controls the electrical fan. But if the coolant isn't circulating. That switch never sends a signal to turn on the fan. But enough talking/rambling. Everyone wants to see pics. The only thing I need to change is the orientation of the handle on the 1" ball valve. I have 2" or more clearance between the handle and the tire when cut hard right. But I still don't like it. And instead of taking the valve out and rotating 180°. I'm just going to take the nut off and rotate the handle 180°. Think I need to make a locking mechanism to lock the handles in place so they don't vibrate closed when the machine is moving.
      The temperature sending unit and housing. Size 22 mm. Aluminum from Amazon.

      Upper Tee the lower Tee is identical. Can also see the handle of the 3/4" ball valve on the 5/8" hose going to the heater.

      The 1" ball valve. Goes between the 2 Tees

      Wide view of the plumbing.

      The heater installed in the sxs. The 3 black hoses are just hanging there. Zip ties to the heater but not attached to any thing. Will probably just direct 2 toward the wife's feet. And 1 toward mine. Or what ever is need as the heat is needed on rides. The black hose in passenger floorboard is some 1" hose that is not needed. Don't know what I'll do with it.

       
      I think if I was going to do it again. I'd put some Indian Head gasket dressing or silicone on the 1" side of the PEX fittings. And I may still do that. But I really hate the ideal of introducing air back in the coolant system.
       
      Any questions just ask. It may take a while to answer. But I'll try.
      Ya be good and stay warm over the next few months 
       
      Kilgore.
    • By mark walkom
      the regen braking on my e1 has stopped working unless (for eg) I am going down a hill in low and it's slowing things down to stick to the 10kph limit. when I drive and take my foot off the accelerator it's not initiating the regen to slow things down and instead just coasts at whatever speed it is at, or speeds up as the regen is not limiting it. the brake lights work, so it's probably not a fault with the sensor on the brake pedal
       
      hoping someone else might be able to provide some suggestions on things to check, as the mob that I bought it off seem to have gone silent on me
×
×
  • Create New...