Quantcast
Jump to content


Type of lift for servicing Kubota rtv- x1140

Andy McGee

By Andy McGee
in Kubota UTV RTV Forum

 Share

Recommended Posts

Andy McGee Newbie

Andy McGee

Posted
Posted

I would like to perform most all my own servicing on the Kubota rtv-x1140. What is the best way to raise the machine for skid plate removal, etc?  I would like it to be parallel with the ground after elevated. It is difficult for me doing that lying under it on the ground.  I’m not certain where safe lift points are. Can I use a residential 2 post car lift?, or is a “drive on” platform the only option?

Link to comment
Share on other sites
  • Alex changed the title to Type of lift for servicing Kubota rtv- x1140
  • 6 months later...
  • 11 months later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • redneckred
      Gremlins in the machine
      By redneckred
      I have a 2012 Bennche Bighorn 700X.  I bought it used.  It had been sitting in a field for several years untouched.  I put a new sun gear in the shifter, new shifter linkage due to the old one having been patched, and a new battery (and of course fresh fuel).  The machine cranked and ran beautifully.  I had it over a year and then the machine quit running.  As it would not stay cranked, I narrowed the problem down to a bad IAC valve.  I replaced it and it ran as good as new/old.  Fast forward, the machine started to act like reverse wasn't catching and would not always back up when in gear.  Then forward quit.  I assumed a bad CVT belt and got one.  Started removing the bolts from the cover and (3) just turn in the housing without coming loose.  (2) are on the bottom, so very little room to do anything with them.  I tried cranking the machine again to see the belt move since I can move the cover enough to see the belt and now the machine will not crank.  It turns over fine.  It gets gas to the injector and has spark.  I can spray cleaner down her throat and she would run until it ran out.  I have replaced the IAC twice and put a new injector with no change.  I went out and put the old injector back in to see if that made any difference and, well, it did.  I tried to crank the machine and the starter is stuck trying to turn the machine over even with the key off.  I have to disconnect the battery to stop it.  Before I shoot this thing, what am I missing?  Is this an ECM problem or something else I am not seeing?  Been dealing with these Gremlins for over a month now and weeds are starting to overtake the motor due to it not moving.  I would love to get the thing running first and any ideas of getting those CVT cover bolts out would be extremely helpful.  Thanks in advance.
    • TPlummer
      Axis x550 02 sensor on right after buying the UTV.
      By TPlummer
      We recently purchased the Axis x550. Fueled it with 93 fuel and drove one time around the farm and the 02 fault error appeared. Any ideas? 
    • Boone
      2014 coleman 700 utv starts idles about 15 seconds then dies any thoughts would be appreciated
      By Boone
      Coleman outfitter 700 efi utv
    • Paul Angstadt
      Hi y'all. New to this stuff. in Florida.
      By Paul Angstadt
      Hi everybody. I just bought a 2012 Hisun with the 700cc engine. Was wondering where i could find a service manual for this thing?
      Its going to need some parts that are missing, like the air intake hoses and other things. Also the dash display is out. the only light that works is neutral light. Not even sure on the model. from pics I've seen, it looks like an HS700. Kind of grey with the black stripes on the hood. Just hoping i can find parts for it.
      Thank you for any advice you can give me. By the way, it does run and goes forward and reverse.
      Paul
    • Hugh
      2018 Hisun Sector Crew 1000 engine die after about 15 minutes run
      By Hugh
      My 2018 Hisun sector crew engine cut off after about 15 minutes run. There is no indicator of what is wrong, no error code just die and won't restart until it cool down. I notice that the fan is not running but the temp indicator is on low temp, no overheat indicator. I checked the radiator fluid, it is cool to touch.
      Cooling fans are working, I can hear it running once awhile if I can get the engine warm up enough.  Thank you for all the help.
       
      Hugh

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...