Quantcast
Jump to content


2021 Massimo T-Boss 550 fuel supply issue

JDSmith

By JDSmith
in Massimo UTV SxS Forum

 Share

Recommended Posts

JDSmith Rookie

JDSmith

Posted
Posted

I have a 2021 Massimo T-Boss 550. It was submerged in water for a period (hurricane). All filters/fluids were drained and replaced/refilled immediately after as well as air box cleaned. Drained fuel tank, popped the supply line off and key cycled to clear the line of contamination. Reconnected line and filled with fresh fuel. The machine fired and sputtered for maybe 30 seconds and died. Upon attempting restart I noted the fuel pump wasn’t priming.  I checked voltage at the pump and it is 12v. I’ve replaced the coil pack, wire, ecu, ignition (which was failing just prior to the water event) and the fuel pump. The new pump still does not engage. Rechecked with new pump and there is 12v at the plug on top of the tank as well as down at the pump. I’ve popped apart all the plugs I can see, sprayed them with terminal cleaner and applied dielectric grease. Still nothing. I’ve talked to a buddy and he has said it has to be a connection or ground issue.  Anyone able to point me to specific plugs wires etc to check? I’m paying for the answer. 😂 

  • Alex changed the title to 2021 Massimo T-Boss 550 fuel supply issue
JDSmith Rookie

JDSmith

Posted
  • Author
Posted

I will have to look for that relay. From what I can see I believe my fuel pump relay is a little different.  I don’t have a relay checked for this type, but I wasn’t thinking it was the issue as I can feel the click in the relay when key is cycled. No more than they cost and it’s not like I haven’t thrown $400-500 at it already I should just try it I suppose.

7A901247-E954-451F-8294-50BD6677DDA1.jpeg

  • 2 weeks later...
JDSmith Rookie

JDSmith

Posted
  • Author
Posted

Tank was drained and refilled. Purged line and reconnected. Started and ran for about 15 sec before dying. Noticed at that time the fuel pump wasn’t priming anymore. 
 

I’ve also replaced the fuel pump. So unless the original and then the new replacement was bad, it’s not the pump.

  • 5 weeks later...
  • 1 month later...
Greg Kilgore Community Regular

Greg Kilgore

Posted
Posted

I know its an older post. But I agree that it seems like it is a ground issue. If the original poster would post his resolution that would help.

But some info on relays and power. And if I wrong it won't be the first time.

The relay should supply the positive 12V DC power. To whatever. The ground or negative side should go to a frame ground or back to the battery.

Frame grounds are a lot of problems on many many electrical issues on a lot of vehicles. Whether it's a side by side or a 2001 GMC Sierra dash cluster (don't ask) or a 1997 Dodge Dakota dash cluster (ground point under the kick panel on driver and passenger side).

Cleaning the ground points or running a ground wire back to the battery should resolve the issue. If the fuel pump and relay is good.  

But usually there are many circuits feeding off one ground point. So it would be best to follow the ground coming off the fuel pump to make sure the ground point is making good contact to frame. 

The ground wire can be tested with a multi-meter.

1. Set multi-meter to OHMS.

2. Hold one lead of multi-meter to the other lead of multi-meter. The reading should be 0.0 to maybe 0.2. That will be the reference of the meter and also tells you there is little to no resistance between the leads.

3. Now take the negative side of the fuel pump wire to one lead of the multi-meter. and touch the other lead to a UNPAINTED part of the frame. The reading should be the same or maybe 0.1 more than when you touch the leads of the meter together. 

If no reading or a very high reading that would indicate a bad connection to ground somewhere and the ground point would need to be cleaned.

 

Hope this info helps you or someone. I'm not responsible if anything unwanted happens while you're testing.

 

JDSmith Rookie

JDSmith

Posted
  • Author
Posted
3 hours ago, Greg Kilgore said:

I know its an older post. But I agree that it seems like it is a ground issue. If the original poster would post his resolution that would help.

But some info on relays and power. And if I wrong it won't be the first time.

The relay should supply the positive 12V DC power. To whatever. The ground or negative side should go to a frame ground or back to the battery.

Frame grounds are a lot of problems on many many electrical issues on a lot of vehicles. Whether it's a side by side or a 2001 GMC Sierra dash cluster (don't ask) or a 1997 Dodge Dakota dash cluster (ground point under the kick panel on driver and passenger side).

Cleaning the ground points or running a ground wire back to the battery should resolve the issue. If the fuel pump and relay is good.  

But usually there are many circuits feeding off one ground point. So it would be best to follow the ground coming off the fuel pump to make sure the ground point is making good contact to frame. 

The ground wire can be tested with a multi-meter.

1. Set multi-meter to OHMS.

2. Hold one lead of multi-meter to the other lead of multi-meter. The reading should be 0.0 to maybe 0.2. That will be the reference of the meter and also tells you there is little to no resistance between the leads.

3. Now take the negative side of the fuel pump wire to one lead of the multi-meter. and touch the other lead to a UNPAINTED part of the frame. The reading should be the same or maybe 0.1 more than when you touch the leads of the meter together. 

If no reading or a very high reading that would indicate a bad connection to ground somewhere and the ground point would need to be cleaned.

 

Hope this info helps you or someone. I'm not responsible if anything unwanted happens while you're testing.

 

 

JDSmith Rookie

JDSmith

Posted
  • Author
Posted

Well we just got it back running…

it was the fuel relay and ecu. Turns out the new ecu was bad as well. A dealer was able to pull a working one off a new unit and it all worked. 
 

the new issue when you put it in reverse it defuels and dies now. The speed sensor is allegedly a common issue, replaced it and same thing. So we just had to leave the speed sensor unplugged and it’s fine. Dealer said Massimo said the causes would be ECU, Speed sensor, or the dash. I’m not replacing the dash so it is just no speedometer for me.

Greg Kilgore Community Regular

Greg Kilgore

Posted
Posted

Glad you got your machine back running. Hopefully the ECU was covered since it was DOA.

I'd guess that since the machine was submerged for a minute or two. There may be more electrical issues pop-up from bad sensors. 

At least the resale value should be higher since your not racking up miles.😁

You may have more relays go in and out or ground issues in the coming future. 

Could an app and cell phone for speed if needed.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Joe Breaux
      2017 Massimo MSU500 Thermostat Malfunction
      By Joe Breaux
      Got a 2017 Massimo MSU500 UTV with thermostat malfunction.. hot light comes on in 4-5 minutes but radiator is ice cold... where exactly is it?  The hose neck on the head has nothing in it.  I was told it was down by oil drain plug.. only thing I see is water pump.. Is in inside pump housing?  Cant find any exploded diagrams that show it.. how to I remove it? any help would be appreciated
    • Alien10
      Snow Blade for Coleman Outfitter 550?
      By Alien10
      I'm thinking of buying a snow blade for my Coleman Outfitter 550 (Hisun with Coleman stickers).
      Has anyone purchased a snow blade that can offer the make and model they bought and any comments, pros  cons etc.?
      Not 100% sure I'm going to buy, as the selection of blades for this model seems a bit thin on line. 
      Thoughts and comments welcomed.
      Thanks in advance.
    • A P
      2022 Hisun Sector 550 eps. Power steering not working
      By A P
      Hi
      I have a 2022 hisun sector eps 550. 30amp fuse is blown for eps. Checked the motor and it’s fine. Opened up the controller and found a bad diode. Dealer wanted 500$ for the controller. Just posting this in case it helps someone. I couldn’t read numbers from the old one so just took a guess and replaced it with a 100v 3amp diode. 
    • Matthew Smith
      SXS No Crank at the Key and No Spark
      By Matthew Smith
      2013 Bennche Bighorn 700 EFI
       I just picked up this project that I was told would crank, but not start.  This is what I’ve figured out so far….
      I installed a new battery and get all dash lights, head lights, and brake lights on when turning the ignition on.  Fuel pump even turns on.  It does not crank with the key, but would when I jumped the starter solenoid, so I replaced it…..no change.
      Figured I’d check for spark and compression while I was dorking around.  Compression is 150 psi, but there is no spark.  Replaced the spark plug… no change.
      So, is my new starter solenoid bad?  Could it be the brake or gear position switches even though the brakes and neutral lights come on?  Not sure where to go from here.




    • SteveS
      2021 Massimo MSU 800 will not run above 20 MPH
      By SteveS
      While driving the MSU 800, it runs good but it lately it will not go over 20 MPH. The side by side will hesitate when it reaches 21 MPH, but it will run good under 20 MPH. What is the issue?

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...