Quantcast
Jump to content


Recommended Posts

Posted

my hisun 400 has ben leaking oil out of a small metal tube on the bottom near the oil filter. Got the side by side given to me after been sitting for a couple years  but 2 quarts in nothing happened my buddy went and worked on it and put another quart in it. i thought it just pushed out what it didn't need. but its dry as a bone inside. does have a good clatter coming from the top end as well, with oil in it. looking for some help not much on the internet about these things.

Posted

Hey Trevor,

Do you have a picture so we can try to help figure out what it is?

Don't run it low on oil, it only holds like 2.5L so 2 low is more or less empty. Running it empty of oil may cause it to self destruct rapidly, which may explain the rattle.

  • 9 months later...
Posted

Mine is doing the same thing! Why isn't their any info for these things online? Same story with me. Bought it for cheap from a family member that couldn't get it running. I got it running but oil was very low. I added oil and it leaks from a tube on the bottom of the engine near the filter. 

  • 3 weeks later...
Posted

I took a picture of it but I can't figure out how to post it here. I'm currently not home to take another one but it is dripping out of a steel nipple that points straight down near the oil filter under the driver's seat. It just drips slowly and after sitting for about three weeks in my barn it looks like at least a quart has dripped out. 

  • 8 months later...
Posted
On 5/29/2023 at 7:19 AM, Casey said:

I took a picture of it but I can't figure out how to post it here. I'm currently not home to take another one but it is dripping out of a steel nipple that points straight down near the oil filter under the driver's seat. It just drips slowly and after sitting for about three weeks in my barn it looks like at least a quart has dripped out. 

there's a nipple under the oil filter that is the water pump weep hole. It shouldn't have oil coming out, you may get a tiny bit of coolant from time to time if the water pump seal is weeping. if theres a flow the water pump seal has failed and you'll need a new water pump.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By CapnWalleye
      Just picked up a Hisun 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • By Homeowner A
      Is there a code reader available for the Coleman UTV 400?  I tried using the HUD ECU Hacker software and cables/adapters but no luck OBD to delphi 6 pin and KKL VAG as well as ELM327.  Will not connect.  I was able to get it to connect randomly a couple of times, but haven't been able to since.  I was able to clear and read the codes briefly.  I'm aware of the Tiny Scan 301 but it doesn't seem to be readily available.  There's a few out there but they are expensive.  
    • By Marie
      hello, i need help figuring out where all these wires go on this battery. I can't seem to find any pictures diagrams. As to what should or shouldn't be attached and where these two plugs go, that aren't plugged in. this was got as a project. would run then die and battery would have to be jumped off to start again stator has now been replaced but any help with this wiring would be appreciated. 
    • By Marie
      Hello, we recently got a 2013 Hisun 800 as a little project for my husband and I to work on. Turns out the guys before us loved the mud anyway. We have replaced the stator and now going to do the Rectifier but here is the hold up as seen in the picture. There are tons of wires going to the battery. I cant seem to find anything that shows what wires should, or shouldn't be attached to the battery or where these 2 plugs go. if someone would please take some pics or share knowledge to where they go I would appreciate it greatly.
    • By A P
      Hi
      I have a 2022 hisun sector eps 550. 30amp fuse is blown for eps. Checked the motor and it’s fine. Opened up the controller and found a bad diode. Dealer wanted 500$ for the controller. Just posting this in case it helps someone. I couldn’t read numbers from the old one so just took a guess and replaced it with a 100v 3amp diode. 
×
×
  • Create New...