Quantcast
Jump to content


K-Mule 4010 Oil Leak

Azul

By Azul
in Kawasaki UTV SxS Forum

 Share

Recommended Posts

Azul Rookie

Azul

Posted
Posted

I have  a 2011, 4010 Gas TransMule with less than 200 hours, and a serious oil leak.  If it is a main seal, what next?  Not oil filter or oil plug.  How do you get to the oil pan?  It has been babied by an old man.

  • Azul changed the title to K-Mule 4010 Oil Leak
Travis Grand Master

Travis

Posted
Posted

Should have a KAF620 v-twin engine,

The main  thing when identifying an oil leak is to CLEAN everything... it makes it easier to trace.

You'll have to remove the  primary clutch and clutch cover, then you'll have access to the PTO oil seal. If it is leaking from the crankcase cover, you just remove the cover and scrape the old gasket and install a new one. might be easier out of the frame but it can be done in frame.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Similar Topics

    • Jim Kessell
      EH65 spitting fuel from breather hose into air filter.
      By Jim Kessell
      2005 American Landmaster
      EH65 Subaru Robins
      spits fuel from breather hose into the air cleaner and then down into carb.  What’s causing this ??
    • mark walkom
      sector e1 regen has stopped (mostly) working
      By mark walkom
      the regen braking on my e1 has stopped working unless (for eg) I am going down a hill in low and it's slowing things down to stick to the 10kph limit. when I drive and take my foot off the accelerator it's not initiating the regen to slow things down and instead just coasts at whatever speed it is at, or speeds up as the regen is not limiting it. the brake lights work, so it's probably not a fault with the sensor on the brake pedal
       
      hoping someone else might be able to provide some suggestions on things to check, as the mob that I bought it off seem to have gone silent on me
    • John M in Louisiana
      Hisun E1 Power Plug Replacement
      By John M in Louisiana
      Quick question about replacing the plug.  One of the prongs pulled out, so I'm thinking it will be an easy fix to connect the old cord with a new plug but I'm unsure about the specs.  15amp 125v?  Is it more complicated than that?  I do plan to buy a plug that's water tight.
      Thanks in advance!
    • Callie
      2021 Bobcat uv34xl gas Keeps Overheating
      By Callie
      We have replaced the relay/fuse, water pump, fan & radiator cap. What are we missing? Fan still won't kick on.
    • Kingfish
      Now that I have done the LI-Ion batt conversion, I need to do something about the suspension
      By Kingfish
      The conversion took about 350lbs. off the vehicle.  It never rode great, but now I feel every  crack in the road.  I have backed off spring compression nut to the point just under where they would move around if suspension was at full extension, but it is still very stiff.  I would like to put some softer coilover springs on it, but I have no idea what the spring rate is with the original springs so I would just be guessing on what to order.  Does anyone have the data for the original spring compression rate?  I am willing to give up a little ground clearance for a softer ride. Right now when sitting still the rear suspension is at or near full extension and the rear tires have several degrees of camber which will cause uneven wear if allowed to continue in this state.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...